News Details

You are here: Home » News » Wood Cutting Tools » Make Your Dowel Drill Bits Drilling More Efficiently By Solving 6 Issues

Make Your Dowel Drill Bits Drilling More Efficiently By Solving 6 Issues

Views:0     Author:Site Editor     Publish Time: 2020-10-27      Origin:Site

Boring drill can be efficient in drilling holes on wooden board. But problems sometimes happen when it works, which make the drilling less efficiency and disturb us a lot. But have you ever considered that once we solved these problems or avoid these problems, our dowel drill bits can work in a higher efficiency? To solve these problems and make the drilling tool speed up, we have collected 6 problems which may happen when you do the wood drilling, and we also provide 6 corresponding solutions to help you deal with these problems and make your dowel drill bits work more efficiently.


carbide drill bits drilling holes


1.Chips around holes after drilling


Sometimes there may be some small broken parts around the hole, make our drilling a failure. To solve this question, except check whether there are influences made by back taper and bit bounce, you also need to check whether the spindle and quick change joint are coaxial,configuration of machine tool compacting device, pressureis enough or not and whether workpiece will shakeor notwhen drilling. It will also create these broken places if cutting edges is higher than the center tip.


2.Entrance hole is small but exit side is big


This problem may be induced by bit bouncing and misalignmentof your main shaft and quick change joint. If there’s such problem happened, you need to check the bit or change the main shaft and the joint.


3.There are drilling smoke and drill bits get dark


Serious central bit bouncing or central bit and shaft are misalign, no positive or back taper, small main relief angle(it should be 12°to 15°), deflection angle of the main rear angle is opposite to rotation of bitswill all lead todrilling smoke and make drill bits get dark. But it may also caused by deficiency of machine toolpressure. If glue which used in boards is not dried or there’s too much glue in boardswill make your drills getting dark, too.


4.Chip removal is not smooth or even don’t work


To solve this problem, you may check if there’re problems like small spiral groove or helicalangle, transition between alloy and cutter body is not smooth enough, primary rear angle is too small to be a secondary value,center tip is too short and thick. Also, before drilling, you need to check whether your dowel drill bits suit your machine or not(2800-3500 RPM is a normal value). Besides, too much glue and if glue is still wet in wooden board will also cause this problem. Or, you may make a simple mistake—make a wrong direction of the rotation.


5.Chips heed up on flank surface


This problem may happen when there is too much glue in processing materials, just change the material you are going to processing or change your bits. In addition, when drill bitsreaches phase transition, it starts to wear seriously, which will also cause a lot of cumulative chips on rear cutter surface during drilling. Andunreasonable production of split cutting edge will also cause a lot of cumulative chips on back surface during drilling.


6.Drill bit bends or breaks when drilling


This problem mainly happened on small size dowel drill bitsor extension dowel drillbits.We will talk about this in two aspects. First, from the bit itself. Small size bithave poorerrigidity than normal dowel drill bits.If itsheat treatment does notbewell treated, it will easily be distorted or broken. Unreasonable design of drill bit helix Angle will also lead tothis problem. In addition, an extended bit or a bit made up ofdefectiveraw materialwill cause the bit to twist and bend orevenbreak during drilling.



drill bits


Secondly, let’s talk it from the side of application. If depth of drill hole is more than four times of the drill bit’s diameter, we call it a “deep hole”. When thereis a deep holeneed to be drill, we need to separate drill process to several times instead of settling a matter at one go. And if you finish it with only one drill, then your dowel drill bits may twist and bend deformation orevenbreak when drilling. Also, RPM of your drill bits should match RPM of your boring machine. Otherwise, your drill bits may also get damaged.Too much glue inplatesor glue istoo wet will easily cause bitsto twist and bend or break when drilling with small specificationdowel drill bits.


board


These are six ways to improve your drilling efficiency. If you have met these problems when you use your dowel drill bits, you can try methods we provide above. Hope these methods can help you and thanks for your reading.


Kone Carbide Tool Co., Ltd.
 
E-mail:   Click to show the Email
 
Tel:  +86-28-61716272
 
Mobile: +86 13648013796

Add:  No. 777 Haike Road Cross-Strait Industrial Park Wenjiang, Chengdu,610000,P.R.China
We use cookies to enable all functionalities for the best performance during your visit and to improve our services by giving us some insight into how the website is being used. Continued use of our website without having changed your browser settings confirms your acceptance of these cookies. For details please see our cookies
×